-#******************************************************************************\r
-#\r
-# Copyright (c) 2019 Intel.\r
-#\r
-# Licensed under the Apache License, Version 2.0 (the "License");\r
-# you may not use this file except in compliance with the License.\r
-# You may obtain a copy of the License at\r
-#\r
-# http://www.apache.org/licenses/LICENSE-2.0\r
-#\r
-# Unless required by applicable law or agreed to in writing, software\r
-# distributed under the License is distributed on an "AS IS" BASIS,\r
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.\r
-# See the License for the specific language governing permissions and\r
-# limitations under the License.\r
-#\r
-#******************************************************************************/\r
-\r
-\r
-# This is simple configuration file. Use '#' sign for comments\r
-instanceId=0 # 0,1,2,... in case more than 1 application started on the same system\r
-appMode=0 # lls-CU(0) | RU(1)\r
-xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)\r
-ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)\r
-antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B \r
-\r
-##Numerology\r
-mu=3 #mmWave 120Khz Sub Carrier Spacing\r
-ttiPeriod=125 # in us TTI period (mmWave default 125us)\r
-nDLAbsFrePointA=27968160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000\r
-nULAbsFrePointA=27968160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000\r
-nDLBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400\r
-nULBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400\r
-nDLFftSize=1024\r
-nULFftSize=1024\r
-\r
-nFrameDuplexType=1 # 0 - FDD 1 - TDD\r
-nTddPeriod=4 #[0-5] TDD priod e.g. DDDS 4\r
-sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-sSlotConfig3=0,2,2,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD\r
-# not used\r
-#sSlotConfig4=0,2,2,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD\r
-#sSlotConfig5=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD\r
-#sSlotConfig6=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-#sSlotConfig7=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-#sSlotConfig8=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-#sSlotConfig9=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD\r
-\r
-MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single \r
- #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)\r
-Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec\r
-Gps_Beta=0\r
-\r
+#******************************************************************************
+#
+# Copyright (c) 2019 Intel.
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+#******************************************************************************/
+
+
+# This is simple configuration file. Use '#' sign for comments
+instanceId=0 # 0,1,2,... in case more than 1 application started on the same system
+appMode=0 # lls-CU(0) | RU(1)
+xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
+ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
+antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
+
+##Numerology
+mu=3 #mmWave 120Khz Sub Carrier Spacing
+ttiPeriod=125 # in us TTI period (mmWave default 125us)
+nDLAbsFrePointA=27968160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nULAbsFrePointA=27968160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nDLBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
+nULBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
+nDLFftSize=1024
+nULFftSize=1024
+
+nFrameDuplexType=1 # 0 - FDD 1 - TDD
+nTddPeriod=4 #[0-5] TDD priod e.g. DDDS 4
+sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig3=0,2,2,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
+# not used
+#sSlotConfig4=0,2,2,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
+#sSlotConfig5=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
+#sSlotConfig6=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+#sSlotConfig7=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+#sSlotConfig8=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+#sSlotConfig9=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+
+MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
+ #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
+Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
+Gps_Beta=0
+
ioCore=5
systemCore=5
pktProcCore=5
pktAuxCore=5
timingCore=6
-llsCUMac=00:11:22:33:44:66 # asigned MAC of lls-CU VF\r
-ruMac=00:11:22:33:44:55 # RU VF for RU app\r
-#ruMac=3c:fd:fe:9e:93:68 #RU PF for tcpdump\r
-\r
-maxFrameId=99 # set for compatibility with O-RU\r
-\r
-numSlots=40 #number of slots per IQ files\r
-antC0=./usecase/mu3_100mhz/ant_0.bin #CC0\r
-antC1=./usecase/mu3_100mhz/ant_1.bin #CC0\r
-antC2=./usecase/mu3_100mhz/ant_2.bin #CC0\r
-antC3=./usecase/mu3_100mhz/ant_3.bin #CC0\r
-antC4=./usecase/mu3_100mhz/ant_4.bin #CC1\r
-antC5=./usecase/mu3_100mhz/ant_5.bin #CC1\r
-antC6=./usecase/mu3_100mhz/ant_6.bin #CC1\r
-antC7=./usecase/mu3_100mhz/ant_7.bin #CC1\r
-antC8=./usecase/mu3_100mhz/ant_8.bin #CC2\r
-antC9=./usecase/mu3_100mhz/ant_9.bin #CC2\r
-antC10=./usecase/mu3_100mhz/ant_10.bin #CC2\r
-antC11=./usecase/mu3_100mhz/ant_11.bin #CC2\r
-antC12=./usecase/mu3_100mhz/ant_12.bin #CC3\r
-antC13=./usecase/mu3_100mhz/ant_13.bin #CC3\r
-antC14=./usecase/mu3_100mhz/ant_14.bin #CC3\r
-antC15=./usecase/mu3_100mhz/ant_15.bin #CC3\r
-\r
-rachEanble=1 # Enable (1)| disable (0) PRACH configuration\r
-prachConfigIndex=81\r
-\r
-## control of IQ byte order\r
-iqswap=0 #do swap of IQ before send buffer to eth\r
-nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order\r
-\r
-##Debug\r
-debugStop=1 #stop app on 1pps boundary (gps_second % 30)\r
-debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary\r
-bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode\r
-\r
-CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled\r
-c_plane_vlan_tag=1 #VLAN Tag used for C-Plane\r
-u_plane_vlan_tag=2 #VLAN Tag used for U-Plane\r
-\r
-##RU Settings\r
-totalBFWeights=32 # Total number of Beamforming Weights on RU\r
-\r
-Tadv_cp_dl=25 #in us TODO: update per RU implementation\r
- #C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages\r
-\r
-#Reception Window C-plane DL\r
-T2a_min_cp_dl=50 #in us \r
-T2a_max_cp_dl=140 #in us \r
-\r
-#Reception Window C-plane UL\r
-T2a_min_cp_ul=50 #in us \r
-T2a_max_cp_ul=140 #in us \r
-\r
-#Reception Window U-plane\r
-T2a_min_up=25 #in us\r
-T2a_max_up=140 #in us\r
-\r
-#Transmission Window\r
-Ta3_min=20 #in us\r
-Ta3_max=32 #in us\r
-\r
-###########################################################\r
-##lls-CU Settings\r
-#C-plane\r
-#Transmission Window Fast C-plane DL\r
-T1a_min_cp_dl=70\r
-T1a_max_cp_dl=100\r
-\r
-##Transmission Window Fast C-plane UL\r
-T1a_min_cp_ul=60\r
-T1a_max_cp_ul=70\r
-\r
-#U-plane\r
-##Transmission Window\r
-T1a_min_up=35\r
-T1a_max_up=50\r
-\r
-#Reception Window\r
-Ta4_min=0\r
-Ta4_max=45\r
-###########################################################\r
-\r
+llsCUMac=00:11:22:33:44:66 # asigned MAC of lls-CU VF
+ruMac=00:11:22:33:44:55 # RU VF for RU app
+#ruMac=3c:fd:fe:9e:93:68 #RU PF for tcpdump
+
+maxFrameId=99 # set for compatibility with O-RU
+
+numSlots=40 #number of slots per IQ files
+antC0=./usecase/mu3_100mhz/ant_0.bin #CC0
+antC1=./usecase/mu3_100mhz/ant_1.bin #CC0
+antC2=./usecase/mu3_100mhz/ant_2.bin #CC0
+antC3=./usecase/mu3_100mhz/ant_3.bin #CC0
+antC4=./usecase/mu3_100mhz/ant_4.bin #CC1
+antC5=./usecase/mu3_100mhz/ant_5.bin #CC1
+antC6=./usecase/mu3_100mhz/ant_6.bin #CC1
+antC7=./usecase/mu3_100mhz/ant_7.bin #CC1
+antC8=./usecase/mu3_100mhz/ant_8.bin #CC2
+antC9=./usecase/mu3_100mhz/ant_9.bin #CC2
+antC10=./usecase/mu3_100mhz/ant_10.bin #CC2
+antC11=./usecase/mu3_100mhz/ant_11.bin #CC2
+antC12=./usecase/mu3_100mhz/ant_12.bin #CC3
+antC13=./usecase/mu3_100mhz/ant_13.bin #CC3
+antC14=./usecase/mu3_100mhz/ant_14.bin #CC3
+antC15=./usecase/mu3_100mhz/ant_15.bin #CC3
+
+rachEanble=1 # Enable (1)| disable (0) PRACH configuration
+prachConfigIndex=81
+
+## control of IQ byte order
+iqswap=0 #do swap of IQ before send buffer to eth
+nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
+
+##Debug
+debugStop=1 #stop app on 1pps boundary (gps_second % 30)
+debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
+bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
+
+CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
+c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
+u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
+
+##RU Settings
+totalBFWeights=32 # Total number of Beamforming Weights on RU
+
+Tadv_cp_dl=25 #in us TODO: update per RU implementation
+ #C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
+
+#Reception Window C-plane DL
+T2a_min_cp_dl=50 #in us
+T2a_max_cp_dl=140 #in us
+
+#Reception Window C-plane UL
+T2a_min_cp_ul=50 #in us
+T2a_max_cp_ul=140 #in us
+
+#Reception Window U-plane
+T2a_min_up=25 #in us
+T2a_max_up=140 #in us
+
+#Transmission Window
+Ta3_min=20 #in us
+Ta3_max=32 #in us
+
+###########################################################
+##lls-CU Settings
+#C-plane
+#Transmission Window Fast C-plane DL
+T1a_min_cp_dl=70
+T1a_max_cp_dl=100
+
+##Transmission Window Fast C-plane UL
+T1a_min_cp_ul=60
+T1a_max_cp_ul=70
+
+#U-plane
+##Transmission Window
+T1a_min_up=35
+T1a_max_up=50
+
+#Reception Window
+Ta4_min=0
+Ta4_max=45
+###########################################################
+
Code Review / o-du / phy.git / blobdiff