--- /dev/null
+#******************************************************************************
+#
+# Copyright (c) 2019 Intel.
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+#******************************************************************************/
+
+# This is simple configuration file. Use '#' sign for comments
+instanceId=1 # 0,1,2,... in case more than 1 application started on the same system
+appMode=1 # O-DU(0) | O-RU(1)
+xranRanTech=1 # 5G-NR (0) | LTE (1)
+xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
+ccNum=6 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
+antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
+
+##Numerology
+mu=0 #15Khz Sub Carrier Spacing
+ttiPeriod=1000 # in us TTI period (15Khz default 1000us)
+nDLAbsFrePointA=2645460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nULAbsFrePointA=2525460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nDLBandwidth=5 #Carrier bandwidth for in MHz. Value: 5->400
+nULBandwidth=5 #Carrier bandwidth for in MHz. Value: 5->400
+nDLFftSize=512
+nULFftSize=512
+
+nFrameDuplexType=0 # 0 - FDD 1 - TDD
+nTddPeriod=0 #TDD priod e.g. DDDS 4
+
+MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
+ #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
+Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
+Gps_Beta=0
+
+ioCore=10
+#ioSleep=1
+
+numSlots=20 #number of slots per IQ files
+antC0=./usecase/dss/mu0_5mhz/ant_0.bin #CC0
+antC1=./usecase/dss/mu0_5mhz/ant_1.bin #CC0
+antC2=./usecase/dss/mu0_5mhz/ant_2.bin #CC0
+antC3=./usecase/dss/mu0_5mhz/ant_3.bin #CC0
+antC4=./usecase/dss/mu0_5mhz/ant_0.bin #CC1
+antC5=./usecase/dss/mu0_5mhz/ant_1.bin #CC1
+antC6=./usecase/dss/mu0_5mhz/ant_2.bin #CC1
+antC7=./usecase/dss/mu0_5mhz/ant_3.bin #CC1
+antC8=./usecase/dss/mu0_5mhz/ant_0.bin #CC2
+antC9=./usecase/dss/mu0_5mhz/ant_1.bin #CC2
+antC10=./usecase/dss/mu0_5mhz/ant_2.bin #CC2
+antC11=./usecase/dss/mu0_5mhz/ant_3.bin #CC2
+antC12=./usecase/dss/mu0_5mhz/ant_0.bin #CC3
+antC13=./usecase/dss/mu0_5mhz/ant_1.bin #CC3
+antC14=./usecase/dss/mu0_5mhz/ant_2.bin #CC3
+antC15=./usecase/dss/mu0_5mhz/ant_3.bin #CC3
+antC16=./usecase/dss/mu0_5mhz/ant_0.bin #CC4
+antC17=./usecase/dss/mu0_5mhz/ant_1.bin #CC4
+antC18=./usecase/dss/mu0_5mhz/ant_2.bin #CC4
+antC19=./usecase/dss/mu0_5mhz/ant_3.bin #CC4
+antC20=./usecase/dss/mu0_5mhz/ant_0.bin #CC5
+antC21=./usecase/dss/mu0_5mhz/ant_1.bin #CC5
+antC22=./usecase/dss/mu0_5mhz/ant_2.bin #CC5
+antC23=./usecase/dss/mu0_5mhz/ant_3.bin #CC5
+
+## RACH TODO: update for PRACH
+rachEnable=0 # Enable (1)| disable (0) PRACH configuration
+#rachOffset=43 # RB offset for prach detection (see RIU spec)
+prachConfigIndex=189 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
+
+antPrachC0=./usecase/lte_a/mu0_20mhz/ant_0.bin
+antPrachC1=./usecase/lte_a/mu0_20mhz/ant_1.bin
+antPrachC2=./usecase/lte_a/mu0_20mhz/ant_2.bin
+antPrachC3=./usecase/lte_a/mu0_20mhz/ant_3.bin
+
+###########################################################
+##Section Settings
+dssEnable=1 # Enable (1)| disable (0) - flag to enable extType-9
+dssPeriod=5
+technology=1,1,0,0,1 #Consider each comma separated value as a technology(NR/LTE) for a given slot. 1-NR, 0-LTE. this pattern repeats after every dssPeriod
+###########################################################
+
+## control of IQ byte order
+iqswap=0 #do swap of IQ before send buffer to eth
+nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
+
+##Debug
+debugStop=1 #stop app on 1pps boundary (gps_second % 30)
+debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
+bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
+
+CPenable=0 #(1) C-Plane is enabled| (0) C-Plane is disabled
+c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
+u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
+
+##RU Settings
+totalBFWeights=32 # Total number of Beamforming Weights on RU
+
+#CID settings
+DU_Port_ID_bitwidth=2
+BandSector_ID_bitwidth=3
+CC_ID_bitwidth=3
+RU_Port_ID_bitwidth=8
+
+# LTE-FDD-FR1-CAT-A-NoBF / LTE-FDD-FR1-CAT-A-DBF
+# O-RAN.WG4.IOT.0-v02.00
+# Table A.2.3.2-1: LTE FDD IOT Profile 2 - LTE-FDD-FR1-CAT-A-NoBF
+
+#U-plane
+##Transmission Window
+T1a_max_up=437
+T1a_min_up=366
+
+#Reception Window U-plane
+T2a_max_up=437
+T2a_min_up=206
+
+Tadv_cp_dl=125
+
+#Transmission Window
+Ta3_max=232 #in us
+Ta3_min=70 #in us
+
+#Reception Window
+Ta4_max=392
+Ta4_min=70
+
+##Transmission Window Fast C-plane UL
+T1a_max_cp_ul=356
+T1a_min_cp_ul=285
+
+#Reception Window C-plane UL
+T2a_max_cp_ul=356 #in us
+T2a_min_cp_ul=125 #in us
+
+###########################################################
+##O-DU Settings
+#C-plane
+#Transmission Window Fast C-plane DL
+T1a_max_cp_dl=562 #in T1a_max_up + Tcp_adv_dl as per Annex B
+T1a_min_cp_dl=491 #in T1a_min_up + Tcp_adv_dl as per Annex B
+
+#O-RU Reception Window C-plane DL
+T2a_max_cp_dl=562 #in T2a_max_up + Tcp_adv_dl as per Annex B
+T2a_min_cp_dl=331 #in T2a_min_up + Tcp_adv_dl as per Annex B
+###########################################################
+
Code Review / o-du / phy.git / blobdiff