--- /dev/null
+#******************************************************************************
+#
+# Copyright (c) 2019 Intel.
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+#******************************************************************************/
+
+# This is simple configuration file. Use '#' sign for comments
+instanceId=1 # 0,1,2,... in case more than 1 application started on the same system
+appMode=1 # O-DU(0) | O-RU(1)
+xranMode=0 # Category A (0) (precoder in O-DU) | Category B (1) (precoder in RU)
+ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
+antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
+
+##Numerology
+mu=1 #30Khz Sub Carrier Spacing
+
+ttiPeriod=500 # in us TTI period (30Khz default 500us)
+
+nDLAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nULAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nDLBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
+nULBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
+nDLFftSize=4096
+nULFftSize=4096
+
+nFrameDuplexType=1 # 0 - FDD 1 - TDD
+nTddPeriod=5 #[0-4] DDDSU, for S it's 10:2:2
+sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig3=0,0,0,0,0,0,0,0,0,0,2,2,1,1 # (0) - DL (1) - UL (2) - GUARD
+sSlotConfig4=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
+
+MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
+ #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
+Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
+Gps_Beta=0
+
+ioCore=15
+# Eth 0
+#duMac0=00:11:22:33:44:66 # asigned MAC of O-DU VF
+#ruMac0=00:11:22:33:44:55 # O-RU VF for O-RU app
+#duMac1=00:11:22:33:44:66 # asigned MAC of O-DU VF
+#ruMac1=00:11:22:33:44:55 # O-RU VF for O-RU app
+
+#Eth 1
+#duMac2=00:11:22:33:44:77 # asigned MAC of O-DU VF
+#ruMac2=00:11:22:33:44:44 # O-RU VF for O-RU app
+#duMac3=00:11:22:33:44:77 # asigned MAC of O-DU VF
+#ruMac3=00:11:22:33:44:44 # O-RU VF for O-RU app
+
+numSlots=20 #number of slots per IQ files
+antC0=./usecase/cat_a/mu1_100mhz/ant_2.bin #CC0
+antC1=./usecase/cat_a/mu1_100mhz/ant_3.bin #CC0
+antC2=./usecase/cat_a/mu1_100mhz/ant_0.bin #CC0
+antC3=./usecase/cat_a/mu1_100mhz/ant_1.bin #CC0
+#antC4=./usecase/cat_a/mu1_100mhz/ant_4.bin #CC1
+#antC5=./usecase/cat_a/mu1_100mhz/ant_5.bin #CC1
+#antC6=./usecase/cat_a/mu1_100mhz/ant_6.bin #CC1
+#antC7=./usecase/cat_a/mu1_100mhz/ant_7.bin #CC1
+#antC8=./usecase/cat_a/mu1_100mhz/ant_8.bin #CC2
+#antC9=./usecase/cat_a/mu1_100mhz/ant_9.bin #CC2
+#antC10=./usecase/cat_a/mu1_100mhz/ant_10.bin #CC2
+#antC11=./usecase/cat_a/mu1_100mhz/ant_11.bin #CC2
+#antC12=./usecase/cat_a/mu1_100mhz/ant_12.bin #CC3
+#antC13=./usecase/cat_a/mu1_100mhz/ant_13.bin #CC3
+#antC14=./usecase/cat_a/mu1_100mhz/ant_14.bin #CC3
+#antC15=./usecase/cat_a/mu1_100mhz/ant_15.bin #CC3
+
+antPrachC0=./usecase/cat_a/mu1_100mhz/ant_0.bin #CC0
+antPrachC1=./usecase/cat_a/mu1_100mhz/ant_1.bin #CC0
+antPrachC2=./usecase/cat_a/mu1_100mhz/ant_2.bin #CC0
+antPrachC3=./usecase/cat_a/mu1_100mhz/ant_3.bin #CC0
+#antPrachC4=./usecase/cat_a/mu1_100mhz/ant_4.bin #CC1
+#antPrachC5=./usecase/cat_a/mu1_100mhz/ant_5.bin #CC1
+#antPrachC6=./usecase/cat_a/mu1_100mhz/ant_6.bin #CC1
+#antPrachC7=./usecase/cat_a/mu1_100mhz/ant_7.bin #CC1
+#antPrachC8=./usecase/cat_a/mu1_100mhz/ant_8.bin #CC2
+#antPrachC9=./usecase/cat_a/mu1_100mhz/ant_9.bin #CC2
+#antPrachC10=./usecase/cat_a/mu1_100mhz/ant_10.bin #CC2
+#antPrachC11=./usecase/cat_a/mu1_100mhz/ant_11.bin #CC2
+#antPrachC12=./usecase/cat_a/mu1_100mhz/ant_12.bin #CC3
+#antPrachC13=./usecase/cat_a/mu1_100mhz/ant_13.bin #CC3
+#antPrachC14=./usecase/cat_a/mu1_100mhz/ant_14.bin #CC3
+#antPrachC15=./usecase/cat_a/mu1_100mhz/ant_15.bin #CC3
+
+rachEnable=1 # Enable (1)| disable (0) PRACH configuration
+prachConfigIndex=147 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
+
+###########################################################
+##Section Settings
+DynamicSectionEna=1 # 1 - enable dynamic section allocation 0 - static sections all RBs are used
+
+nPrbElemDl=2
+#nRBStart, nRBSize, nStartSymb, numSymb, nBeamIndex, bf_weight_update, compMethod, iqWidth, BeamFormingType
+# weight base beams
+PrbElemDl0=0,137,0,14,0,0,0,16,0
+PrbElemDl1=137,136,0,14,0,0,0,16,0
+#PrbElemDl2=72,36,0,14,3,1,0,16,1
+#PrbElemDl3=108,36,0,14,4,1,0,16,1
+#PrbElemDl4=144,36,0,14,5,1,0,16,1
+#PrbElemDl5=180,36,0,14,6,1,0,16,1
+#PrbElemDl6=216,36,0,14,7,1,0,16,1
+#PrbElemDl7=252,21,0,14,8,1,0,16,1
+
+
+nPrbElemUl=2
+#nRBStart, nRBSize, nStartSymb, numSymb, nBeamIndex, bf_weight_update, compMethod, iqWidth, BeamFormingType
+# weight base beams
+PrbElemUl0=0,137,0,14,0,0,0,16,0
+PrbElemUl1=137,136,0,14,0,0,0,16,0
+#PrbElemUl2=72,36,0,14,3,1,0,16,1
+#PrbElemUl3=108,36,0,14,4,1,0,16,1
+#PrbElemUl4=144,36,0,14,5,1,0,16,1
+#PrbElemUl5=180,36,0,14,6,1,0,16,1
+#PrbElemUl6=216,36,0,14,7,1,0,16,1
+#PrbElemUl7=252,21,0,14,8,1,0,16,1
+
+###########################################################
+
+## control of IQ byte order
+iqswap=0 #do swap of IQ before send buffer to eth
+nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
+
+##Debug
+debugStop=1 #stop app on 1pps boundary (gps_second % 30)
+debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
+bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
+
+CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
+
+##O-RU Settings
+Tadv_cp_dl=125 # in us
+ # C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
+#Reception Window C-plane DL
+T2a_min_cp_dl=419 # 285.42us
+T2a_max_cp_dl=470 # 428.12us
+
+#Reception Window C-plane UL
+T2a_min_cp_ul=125 # 285.42us
+T2a_max_cp_ul=336 # 428.12us
+
+#Reception Window U-plane
+T2a_min_up=134 # 71.35in us
+T2a_max_up=345 # 428.12us
+
+#Transmission Window
+Ta3_min=50 # in us
+Ta3_max=171 # in us
+
+###########################################################
+##O-DU Settings
+#C-plane
+#Transmission Window Fast C-plane DL
+T1a_min_cp_dl=419
+T1a_max_cp_dl=470
+
+##Transmission Window Fast C-plane UL
+T1a_min_cp_ul=285
+T1a_max_cp_ul=336
+
+#U-plane
+##Transmission Window
+T1a_min_up=294 #71 + 25 us
+T1a_max_up=345 #71 + 25 us
+
+#Reception Window
+Ta4_min=50 # in us
+Ta4_max=331 # in us
+###########################################################
+
Code Review / o-du / phy.git / blobdiff