1 #******************************************************************************
3 # Copyright (c) 2019 Intel.
5 # Licensed under the Apache License, Version 2.0 (the "License");
6 # you may not use this file except in compliance with the License.
7 # You may obtain a copy of the License at
9 # http://www.apache.org/licenses/LICENSE-2.0
11 # Unless required by applicable law or agreed to in writing, software
12 # distributed under the License is distributed on an "AS IS" BASIS,
13 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
14 # See the License for the specific language governing permissions and
15 # limitations under the License.
17 #******************************************************************************/
19 #TDD 1 8T8R 100 4 2 64QAM 0.5 16QAM 0.5 66% 180 33% 90 3.425 1.15 DU
22 # This is simple configuration file. Use '#' sign for comments
23 instanceId=1 # 0,1,2,... in case more than 1 application started on the same system
24 appMode=1 # O-DU(0) | O-RU(1)
25 xranMode=1 # Category A (0) (precoder in O-DU) | Category B (1) (precoder in O-RU)
26 ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 4)
27 antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
28 antNumUL=2 # Cat B: UL Number of Antennas per CC (default: 8) or number of UL Digital streams for Category B
29 antElmTRx=8 #number of Antenna Elements for Cat B default 32T32R
32 muMimoUEs=8 #number of UEs serviced by MU-MIMO system. Number of independent beams within the same Freq/Time resources
33 DlLayersPerUe=1 #number of RX anntennas on DL UE side
34 UlLayersPerUe=1 #number of TX anntennas on UL UE side
38 mu=1 #30Khz Sub Carrier Spacing
40 ttiPeriod=500 # in us TTI period (30Khz default 500us)
42 nDLAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
43 nULAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
44 nDLBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
45 nULBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
49 nFrameDuplexType=1 # 0 - FDD 1 - TDD
50 nTddPeriod=10 #[0-9] DDDSUUDDDD, for S it's 6:4:4
51 sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
52 sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
53 sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
54 sSlotConfig3=0,0,0,0,0,0,2,2,2,2,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
55 sSlotConfig4=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
56 sSlotConfig5=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
57 sSlotConfig6=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
58 sSlotConfig7=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
59 sSlotConfig8=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
60 sSlotConfig9=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
62 MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
63 #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
64 Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
69 duMac0=00:11:22:33:44:66 # asigned MAC of O-DU VF
70 ruMac0=00:11:22:33:44:55 # O-RU VF for O-RU app
71 duMac1=00:11:22:33:44:66 # asigned MAC of O-DU VF
72 ruMac1=00:11:22:33:44:55 # O-RU VF for O-RU app
75 duMac2=00:11:22:33:44:77 # asigned MAC of O-DU VF
76 ruMac2=00:11:22:33:44:44 # O-RU VF for O-RU app
77 duMac3=00:11:22:33:44:77 # asigned MAC of O-DU VF
78 ruMac3=00:11:22:33:44:44 # O-RU VF for O-RU app
80 numSlots=20 #number of slots per IQ files
81 antC0=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC0
82 antC1=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC0
83 antC2=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC0
84 antC3=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC0
85 antC4=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC1
86 antC5=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC1
87 antC6=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC1
88 antC7=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC1
89 antC8=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC2
90 antC9=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC2
91 antC10=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC2
92 antC11=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC2
93 antC12=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC3
94 antC13=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC3
95 antC14=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC3
96 antC15=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC3
98 antPrachC0=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC0
99 antPrachC1=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC0
100 antPrachC2=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC0
101 antPrachC3=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC0
102 antPrachC4=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC1
103 antPrachC5=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC1
104 antPrachC6=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC1
105 antPrachC7=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC1
106 antPrachC8=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC2
107 antPrachC9=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC2
108 antPrachC10=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC2
109 antPrachC11=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC2
110 antPrachC12=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC3
111 antPrachC13=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC3
112 antPrachC14=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC3
113 antPrachC15=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC3
115 rachEanble=0 # Enable (1)| disable (0) PRACH configuration
118 srsEanble=1 # Enable (1)| disable (0) SRS
119 srsSym=8192 # (1<<13) symbol used for SRS (def: sym 13)
121 antSrsC0=./usecase/cat_b/mu1_100mhz/ant_0.bin
122 antSrsC1=./usecase/cat_b/mu1_100mhz/ant_1.bin
123 antSrsC2=./usecase/cat_b/mu1_100mhz/ant_2.bin
124 antSrsC3=./usecase/cat_b/mu1_100mhz/ant_3.bin
125 antSrsC4=./usecase/cat_b/mu1_100mhz/ant_4.bin
126 antSrsC5=./usecase/cat_b/mu1_100mhz/ant_5.bin
127 antSrsC6=./usecase/cat_b/mu1_100mhz/ant_6.bin
128 antSrsC7=./usecase/cat_b/mu1_100mhz/ant_7.bin
129 antSrsC8=./usecase/cat_b/mu1_100mhz/ant_0.bin
130 antSrsC9=./usecase/cat_b/mu1_100mhz/ant_1.bin
131 antSrsC10=./usecase/cat_b/mu1_100mhz/ant_2.bin
132 antSrsC11=./usecase/cat_b/mu1_100mhz/ant_3.bin
133 antSrsC12=./usecase/cat_b/mu1_100mhz/ant_4.bin
134 antSrsC13=./usecase/cat_b/mu1_100mhz/ant_5.bin
135 antSrsC14=./usecase/cat_b/mu1_100mhz/ant_6.bin
136 antSrsC15=./usecase/cat_b/mu1_100mhz/ant_7.bin
137 antSrsC16=./usecase/cat_b/mu1_100mhz/ant_0.bin
138 antSrsC17=./usecase/cat_b/mu1_100mhz/ant_1.bin
139 antSrsC18=./usecase/cat_b/mu1_100mhz/ant_2.bin
140 antSrsC19=./usecase/cat_b/mu1_100mhz/ant_3.bin
141 antSrsC20=./usecase/cat_b/mu1_100mhz/ant_4.bin
142 antSrsC21=./usecase/cat_b/mu1_100mhz/ant_5.bin
143 antSrsC22=./usecase/cat_b/mu1_100mhz/ant_6.bin
144 antSrsC23=./usecase/cat_b/mu1_100mhz/ant_7.bin
145 antSrsC24=./usecase/cat_b/mu1_100mhz/ant_0.bin
146 antSrsC25=./usecase/cat_b/mu1_100mhz/ant_1.bin
147 antSrsC26=./usecase/cat_b/mu1_100mhz/ant_2.bin
148 antSrsC27=./usecase/cat_b/mu1_100mhz/ant_3.bin
149 antSrsC28=./usecase/cat_b/mu1_100mhz/ant_4.bin
150 antSrsC29=./usecase/cat_b/mu1_100mhz/ant_5.bin
151 antSrsC30=./usecase/cat_b/mu1_100mhz/ant_6.bin
152 antSrsC31=./usecase/cat_b/mu1_100mhz/ant_7.bin
154 #DL PRB / % Used RBs UL PRB / % Used RBs
157 ###########################################################
159 DynamicSectionEna=1 # 1 - enable dynamic section allocation 0 - static sections all RBs are used
162 #nRBStart, nRBSize, nStartSymb, numSymb, nBeamIndex, bf_weight_update, compMethod, iqWidth, BeamFormingType, Scalefactor, REMask
164 PrbElemDl0=0,90,0,14,0,1,4,1,1,8192,4095
165 PrbElemDl1=90,90,0,14,1,1,4,1,1,8192,4095
168 #nRBStart, nRBSize, nStartSymb, numSymb, nBeamIndex, bf_weight_update, compMethod, iqWidth, BeamFormingType
170 PrbElemUl0=0,64,0,14,0,1,1,9,1
171 PrbElemUl1=64,26,0,14,1,1,1,9,1
173 ###########################################################
175 ## control of IQ byte order
176 iqswap=0 #do swap of IQ before send buffer to eth
177 nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
178 compression=1 # (1) compression enabled (0) compression disabled
181 debugStop=1 #stop app on 1pps boundary (gps_second % 30)
182 debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
183 bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
185 CPenable=0 #(1) C-Plane is enabled| (0) C-Plane is disabled
188 totalBFWeights=32 # Total number of Beamforming Weights on RU
190 Tadv_cp_dl=25 # in us
191 # C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
192 #Reception Window C-plane DL
193 T2a_min_cp_dl=285 # 285.42us
194 T2a_max_cp_dl=429 # 428.12us
196 #Reception Window C-plane UL
197 T2a_min_cp_ul=285 # 285.42us
198 T2a_max_cp_ul=429 # 428.12us
200 #Reception Window U-plane
201 T2a_min_up=71 # 71.35in us
202 T2a_max_up=428 # 428.12us
208 ###########################################################
211 #Transmission Window Fast C-plane DL
215 ##Transmission Window Fast C-plane UL
220 ##Transmission Window
221 T1a_min_up=96 #71 + 25 us
222 T1a_max_up=196 #71 + 25 us
227 ###########################################################