+++ /dev/null
-#******************************************************************************
-#
-# Copyright (c) 2019 Intel.
-#
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at
-#
-# http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-#
-#******************************************************************************/
-
-
-# This is simple configuration file. Use '#' sign for comments
-instanceId=0 # 0,1,2,... in case more than 1 application started on the same system
-appMode=0 # lls-CU(0) | RU(1)
-xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
-ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
-antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
-
-##Numerology
-mu=0 #15Khz Sub Carrier Spacing
-ttiPeriod=1000 # in us TTI period (15Khz default 1000us)
-nDLAbsFrePointA=2645460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
-nULAbsFrePointA=2525460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
-nDLBandwidth=5 #Carrier bandwidth for in MHz. Value: 5->400
-nULBandwidth=5 #Carrier bandwidth for in MHz. Value: 5->400
-nDLFftSize=512
-nULFftSize=512
-
-nFrameDuplexType=0 # 0 - FDD 1 - TDD
-nTddPeriod=0 #TDD priod e.g. DDDS 4
-
-MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
- #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
-Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
-Gps_Beta=0
-
-ioCore=5
-# Eth 0
-duMac0=00:11:22:33:44:66 # asigned MAC of O-DU VF
-ruMac0=00:11:22:33:44:55 # O-RU VF for O-RU app
-duMac1=00:11:22:33:44:66 # asigned MAC of O-DU VF
-ruMac1=00:11:22:33:44:55 # O-RU VF for O-RU app
-
-#Eth 1
-duMac2=00:11:22:33:44:77 # asigned MAC of O-DU VF
-ruMac2=00:11:22:33:44:44 # O-RU VF for O-RU app
-duMac3=00:11:22:33:44:77 # asigned MAC of O-DU VF
-ruMac3=00:11:22:33:44:44 # O-RU VF for O-RU app
-
-numSlots=40 #number of slots per IQ files
-
-antC0=./usecase/mu0_5mhz/ant_0.bin #CC0
-antC1=./usecase/mu0_5mhz/ant_1.bin #CC0
-antC2=./usecase/mu0_5mhz/ant_2.bin #CC0
-antC3=./usecase/mu0_5mhz/ant_3.bin #CC0
-antC4=./usecase/mu0_5mhz/ant_4.bin #CC1
-antC5=./usecase/mu0_5mhz/ant_5.bin #CC1
-antC6=./usecase/mu0_5mhz/ant_6.bin #CC1
-antC7=./usecase/mu0_5mhz/ant_7.bin #CC1
-antC8=./usecase/mu0_5mhz/ant_8.bin #CC2
-antC9=./usecase/mu0_5mhz/ant_9.bin #CC2
-antC10=./usecase/mu0_5mhz/ant_10.bin #CC2
-antC11=./usecase/mu0_5mhz/ant_11.bin #CC2
-antC12=./usecase/mu0_5mhz/ant_12.bin #CC3
-antC13=./usecase/mu0_5mhz/ant_13.bin #CC3
-antC14=./usecase/mu0_5mhz/ant_14.bin #CC3
-antC15=./usecase/mu0_5mhz/ant_15.bin #CC3
-
-## RACH TODO: update for PRACH
-rachEanble=0 # Enable (1)| disable (0) PRACH configuration
-#rachOffset=43 # RB offset for prach detection (see RIU spec)
-#prachConfigIndex=1 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
-
-## control of IQ byte order
-iqswap=0 #do swap of IQ before send buffer to eth
-nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
-
-##Debug
-debugStop=1 #stop app on 1pps boundary (gps_second % 30)
-debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
-bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
-
-CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
-c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
-u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
-
-##RU Settings
-totalBFWeights=32 # Total number of Beamforming Weights on RU
-
-Tadv_cp_dl=25 #in us TODO: update per RU implementation
- #C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
-
-#Reception Window C-plane DL
-T2a_min_cp_dl=400 #in us
-T2a_max_cp_dl=1120 #in us
-
-#Reception Window C-plane UL
-T2a_min_cp_ul=400 #in us
-T2a_max_cp_ul=1120 #in us
-
-#Reception Window U-plane
-T2a_min_up=200 # in us
-T2a_max_up=1120 # in us
-
-#Transmission Window
-Ta3_min=160 #in us
-Ta3_max=256 #in us
-
-###########################################################
-##lls-CU Settings
-#C-plane
-#Transmission Window Fast C-plane DL
-T1a_min_cp_dl=560
-T1a_max_cp_dl=800
-
-##Transmission Window Fast C-plane UL
-T1a_min_cp_ul=480
-T1a_max_cp_ul=560
-
-#U-plane
-##Transmission Window
-T1a_min_up=280
-T1a_max_up=400
-
-#Reception Window
-Ta4_min=0
-Ta4_max=360
-###########################################################
-
Code Review / o-du / phy.git / blobdiff