-#######################################################################
+#******************************************************************************
#
-# <COPYRIGHT_TAG>
+# Copyright (c) 2019 Intel.
#
-#######################################################################
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+#******************************************************************************/
+
# This is simple configuration file. Use '#' sign for comments
+instanceId=0 # 0,1,2,... in case more than 1 application started on the same system
appMode=0 # lls-CU(0) | RU(1)
xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
-ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 4)
-antNum=4 # Number of Antennas per CC (default: 4)
+ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
+antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
##Numerology
mu=0 #15Khz Sub Carrier Spacing
MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
#xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
-
-llsCUMac=00:11:22:33:44:66 # asigned MAC of lls-CU VF
-ruMac=00:11:22:33:44:55 #RU VF for RU app
+Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
+Gps_Beta=0
+
+ioCore=5
+# Eth 0
+duMac0=00:11:22:33:44:66 # asigned MAC of O-DU VF
+ruMac0=00:11:22:33:44:55 # O-RU VF for O-RU app
+duMac1=00:11:22:33:44:66 # asigned MAC of O-DU VF
+ruMac1=00:11:22:33:44:55 # O-RU VF for O-RU app
+
+#Eth 1
+duMac2=00:11:22:33:44:77 # asigned MAC of O-DU VF
+ruMac2=00:11:22:33:44:44 # O-RU VF for O-RU app
+duMac3=00:11:22:33:44:77 # asigned MAC of O-DU VF
+ruMac3=00:11:22:33:44:44 # O-RU VF for O-RU app
+
+numSlots=40 #number of slots per IQ files
antC0=./usecase/mu0_20mhz/ant_0.bin #CC0
antC1=./usecase/mu0_20mhz/ant_1.bin #CC0
antC2=./usecase/mu0_20mhz/ant_2.bin #CC0
antC15=./usecase/mu0_20mhz/ant_15.bin #CC3
## RACH TODO: update for PRACH
-rachEanble=0 # Enable (1)| disable (0) PRACH configuration
+rachEanble=1 # Enable (1)| disable (0) PRACH configuration
#rachOffset=43 # RB offset for prach detection (see RIU spec)
#rachCfgIdx=14 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
+
## control of IQ byte order
iqswap=0 #do swap of IQ before send buffer to eth
nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
##Debug
debugStop=1 #stop app on 1pps boundary (gps_second % 30)
debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
+bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
##RU Settings
+totalBFWeights=32 # Total number of Beamforming Weights on RU
+
Tadv_cp_dl=25 #in us TODO: update per RU implementation
#C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
Code Review / o-du / phy.git / blobdiff