1 #******************************************************************************
3 # Copyright (c) 2019 Intel.
5 # Licensed under the Apache License, Version 2.0 (the "License");
6 # you may not use this file except in compliance with the License.
7 # You may obtain a copy of the License at
9 # http://www.apache.org/licenses/LICENSE-2.0
11 # Unless required by applicable law or agreed to in writing, software
12 # distributed under the License is distributed on an "AS IS" BASIS,
13 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
14 # See the License for the specific language governing permissions and
15 # limitations under the License.
17 #******************************************************************************/
19 #TDD DDDSUUDDDD: S it's 6:4:4 1 8T8R 100 8 4 70.3% 192 2304 70.0% 191 2292 new added 70% with 8T8R
21 # This is simple configuration file. Use '#' sign for comments
22 instanceId=1 # 0,1,2,... in case more than 1 application started on the same system
23 appMode=1 # O-DU(0) | O-RU(1)
24 xranMode=1 # Category A (0) (precoder in O-DU) | Category B (1) (precoder in O-RU)
25 ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 4)
26 antNum=8 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
27 antNumUL=8 # Cat B: UL Number of Antennas per CC (default: 8) or number of UL Digital streams for Category B
28 antElmTRx=8 #number of Antenna Elements for Cat B default 32T32R
31 muMimoUEs=8 #number of UEs serviced by MU-MIMO system. Number of independent beams within the same Freq/Time resources
32 DlLayersPerUe=1 #number of RX anntennas on DL UE side
33 UlLayersPerUe=1 #number of TX anntennas on UL UE side
37 mu=1 #30Khz Sub Carrier Spacing
39 ttiPeriod=500 # in us TTI period (30Khz default 500us)
41 nDLAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
42 nULAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
43 nDLBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
44 nULBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400
48 nFrameDuplexType=1 # 0 - FDD 1 - TDD
49 nTddPeriod=10 #[0-9] DDDSUUDDDD, for S it's 6:4:4
50 sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
51 sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
52 sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
53 sSlotConfig3=0,0,0,0,0,0,2,2,2,2,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
54 sSlotConfig4=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
55 sSlotConfig5=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
56 sSlotConfig6=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
57 sSlotConfig7=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
58 sSlotConfig8=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
59 sSlotConfig9=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
61 MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
62 #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
63 Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
71 llsCUMac=00:11:22:33:44:66 # asigned MAC of O-DU VF
72 ruMac=00:11:22:33:44:55 # O-RU VF for O-RU app
74 numSlots=10 #number of slots per IQ files
75 antC0=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC0
76 antC1=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC0
77 antC2=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC0
78 antC3=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC0
79 antC4=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC1
80 antC5=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC1
81 antC6=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC1
82 antC7=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC1
83 antC8=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC2
84 antC9=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC2
85 antC10=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC2
86 antC11=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC2
87 antC12=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC3
88 antC13=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC3
89 antC14=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC3
90 antC15=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC3
92 antPrachC0=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC0
93 antPrachC1=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC0
94 antPrachC2=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC0
95 antPrachC3=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC0
96 antPrachC4=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC1
97 antPrachC5=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC1
98 antPrachC6=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC1
99 antPrachC7=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC1
100 antPrachC8=./usecase/cat_b/mu1_100mhz/ant_0.bin #CC2
101 antPrachC9=./usecase/cat_b/mu1_100mhz/ant_1.bin #CC2
102 antPrachC10=./usecase/cat_b/mu1_100mhz/ant_2.bin #CC2
103 antPrachC11=./usecase/cat_b/mu1_100mhz/ant_3.bin #CC2
104 antPrachC12=./usecase/cat_b/mu1_100mhz/ant_4.bin #CC3
105 antPrachC13=./usecase/cat_b/mu1_100mhz/ant_5.bin #CC3
106 antPrachC14=./usecase/cat_b/mu1_100mhz/ant_6.bin #CC3
107 antPrachC15=./usecase/cat_b/mu1_100mhz/ant_7.bin #CC3
109 rachEanble=0 # Enable (1)| disable (0) PRACH configuration
112 srsEanble=1 # Enable (1)| disable (0) SRS
113 srsSym=8192 # (1<<13) symbol used for SRS (def: sym 13)
115 antSrsC0=./usecase/cat_b/mu1_100mhz/ant_0.bin
116 antSrsC1=./usecase/cat_b/mu1_100mhz/ant_1.bin
117 antSrsC2=./usecase/cat_b/mu1_100mhz/ant_2.bin
118 antSrsC3=./usecase/cat_b/mu1_100mhz/ant_3.bin
119 antSrsC4=./usecase/cat_b/mu1_100mhz/ant_4.bin
120 antSrsC5=./usecase/cat_b/mu1_100mhz/ant_5.bin
121 antSrsC6=./usecase/cat_b/mu1_100mhz/ant_6.bin
122 antSrsC7=./usecase/cat_b/mu1_100mhz/ant_7.bin
123 antSrsC8=./usecase/cat_b/mu1_100mhz/ant_0.bin
124 antSrsC9=./usecase/cat_b/mu1_100mhz/ant_1.bin
125 antSrsC10=./usecase/cat_b/mu1_100mhz/ant_2.bin
126 antSrsC11=./usecase/cat_b/mu1_100mhz/ant_3.bin
127 antSrsC12=./usecase/cat_b/mu1_100mhz/ant_4.bin
128 antSrsC13=./usecase/cat_b/mu1_100mhz/ant_5.bin
129 antSrsC14=./usecase/cat_b/mu1_100mhz/ant_6.bin
130 antSrsC15=./usecase/cat_b/mu1_100mhz/ant_7.bin
131 antSrsC16=./usecase/cat_b/mu1_100mhz/ant_0.bin
132 antSrsC17=./usecase/cat_b/mu1_100mhz/ant_1.bin
133 antSrsC18=./usecase/cat_b/mu1_100mhz/ant_2.bin
134 antSrsC19=./usecase/cat_b/mu1_100mhz/ant_3.bin
135 antSrsC20=./usecase/cat_b/mu1_100mhz/ant_4.bin
136 antSrsC21=./usecase/cat_b/mu1_100mhz/ant_5.bin
137 antSrsC22=./usecase/cat_b/mu1_100mhz/ant_6.bin
138 antSrsC23=./usecase/cat_b/mu1_100mhz/ant_7.bin
139 antSrsC24=./usecase/cat_b/mu1_100mhz/ant_0.bin
140 antSrsC25=./usecase/cat_b/mu1_100mhz/ant_1.bin
141 antSrsC26=./usecase/cat_b/mu1_100mhz/ant_2.bin
142 antSrsC27=./usecase/cat_b/mu1_100mhz/ant_3.bin
143 antSrsC28=./usecase/cat_b/mu1_100mhz/ant_4.bin
144 antSrsC29=./usecase/cat_b/mu1_100mhz/ant_5.bin
145 antSrsC30=./usecase/cat_b/mu1_100mhz/ant_6.bin
146 antSrsC31=./usecase/cat_b/mu1_100mhz/ant_7.bin
149 ###########################################################
151 DynamicSectionEna=1 # 1 - enable dynamic section allocation 0 - static sections all RBs are used
154 #nRBStart, nRBSize, nStartSymb, numSymb, nBeamIndex, bf_weight_update, compMethod, iqWidth, BeamFormingType
156 PrbElemDl0=0,48,0,14,1,1,1,9,1
157 PrbElemDl1=48,48,0,14,2,1,1,9,1
158 PrbElemDl2=96,48,0,14,3,1,1,9,1
159 PrbElemDl3=144,48,0,14,4,1,1,9,1
162 #nRBStart, nRBSize, nStartSymb, numSymb, nBeamIndex, bf_weight_update, compMethod, iqWidth, BeamFormingType
164 PrbElemUl0=0,48,0,14,1,1,1,9,1
165 PrbElemUl1=48,48,0,14,2,1,1,9,1
166 PrbElemUl2=96,48,0,14,3,1,1,9,1
167 PrbElemUl3=144,48,0,14,4,1,1,9,1
169 ###########################################################
171 ## control of IQ byte order
172 iqswap=0 #do swap of IQ before send buffer to eth
173 nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
174 compression=1 # (1) compression enabled (0) compression disabled
177 debugStop=1 #stop app on 1pps boundary (gps_second % 30)
178 debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
179 bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
181 CPenable=0 #(1) C-Plane is enabled| (0) C-Plane is disabled
184 totalBFWeights=32 # Total number of Beamforming Weights on RU
186 Tadv_cp_dl=25 # in us
187 # C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
188 #Reception Window C-plane DL
189 T2a_min_cp_dl=285 # 285.42us
190 T2a_max_cp_dl=429 # 428.12us
192 #Reception Window C-plane UL
193 T2a_min_cp_ul=285 # 285.42us
194 T2a_max_cp_ul=429 # 428.12us
196 #Reception Window U-plane
197 T2a_min_up=71 # 71.35in us
198 T2a_max_up=428 # 428.12us
204 ###########################################################
207 #Transmission Window Fast C-plane DL
211 ##Transmission Window Fast C-plane UL
216 ##Transmission Window
217 T1a_min_up=96 #71 + 25 us
218 T1a_max_up=196 #71 + 25 us
223 ###########################################################