1 #######################################################################
5 #######################################################################
7 # This is simple configuration file. Use '#' sign for comments
8 appMode=1 # lls-CU(0) | RU(1)
9 xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
10 ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 4)
11 antNum=4 # Number of Antennas per CC (default: 4)
14 mu=0 #15Khz Sub Carrier Spacing
15 ttiPeriod=1000 # in us TTI period (15Khz default 1000us)
16 nDLAbsFrePointA=2645460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
17 nULAbsFrePointA=2525460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
18 nDLBandwidth=5 #Carrier bandwidth for in MHz. Value: 5->400
19 nULBandwidth=5 #Carrier bandwidth for in MHz. Value: 5->400
23 nFrameDuplexType=0 # 0 - FDD 1 - TDD
24 nTddPeriod=0 #TDD priod e.g. DDDS 4
26 MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
27 #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
29 llsCUMac=00:11:22:33:44:66 # asigned MAC of lls-CU VF
30 ruMac=00:11:22:33:44:55 #RU VF for RU app
31 antC0=./usecase/mu0_5mhz/ant_0.bin #CC0
32 antC1=./usecase/mu0_5mhz/ant_1.bin #CC0
33 antC2=./usecase/mu0_5mhz/ant_2.bin #CC0
34 antC3=./usecase/mu0_5mhz/ant_3.bin #CC0
35 antC4=./usecase/mu0_5mhz/ant_4.bin #CC1
36 antC5=./usecase/mu0_5mhz/ant_5.bin #CC1
37 antC6=./usecase/mu0_5mhz/ant_6.bin #CC1
38 antC7=./usecase/mu0_5mhz/ant_7.bin #CC1
39 antC8=./usecase/mu0_5mhz/ant_8.bin #CC2
40 antC9=./usecase/mu0_5mhz/ant_9.bin #CC2
41 antC10=./usecase/mu0_5mhz/ant_10.bin #CC2
42 antC11=./usecase/mu0_5mhz/ant_11.bin #CC2
43 antC12=./usecase/mu0_5mhz/ant_12.bin #CC3
44 antC13=./usecase/mu0_5mhz/ant_13.bin #CC3
45 antC14=./usecase/mu0_5mhz/ant_14.bin #CC3
46 antC15=./usecase/mu0_5mhz/ant_15.bin #CC3
48 ## RACH TODO: update for PRACH
49 rachEanble=0 # Enable (1)| disable (0) PRACH configuration
50 #rachOffset=43 # RB offset for prach detection (see RIU spec)
51 #prachConfigIndex=1 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
53 ## control of IQ byte order
54 iqswap=0 #do swap of IQ before send buffer to eth
55 nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
58 debugStop=1 #stop app on 1pps boundary (gps_second % 30)
59 debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
61 CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
62 c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
63 u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
66 Tadv_cp_dl=25 #in us TODO: update per RU implementation
67 #C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
69 #Reception Window C-plane DL
70 T2a_min_cp_dl=400 #in us
71 T2a_max_cp_dl=1120 #in us
73 #Reception Window C-plane UL
74 T2a_min_cp_ul=400 #in us
75 T2a_max_cp_ul=1120 #in us
77 #Reception Window U-plane
78 T2a_min_up=200 # in us
79 T2a_max_up=1120 # in us
85 ###########################################################
88 #Transmission Window Fast C-plane DL
92 ##Transmission Window Fast C-plane UL
104 ###########################################################