1 #******************************************************************************
3 # Copyright (c) 2019 Intel.
5 # Licensed under the Apache License, Version 2.0 (the "License");
6 # you may not use this file except in compliance with the License.
7 # You may obtain a copy of the License at
9 # http://www.apache.org/licenses/LICENSE-2.0
11 # Unless required by applicable law or agreed to in writing, software
12 # distributed under the License is distributed on an "AS IS" BASIS,
13 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
14 # See the License for the specific language governing permissions and
15 # limitations under the License.
17 #******************************************************************************/
20 # This is simple configuration file. Use '#' sign for comments
21 instanceId=0 # 0,1,2,... in case more than 1 application started on the same system
22 appMode=0 # O-DU (0) | RU(1)
23 xranRanTech=1 # 5G NR (0) | LTE (1)
24 xranMode=0 # Category A (0) (precoder in O-DU) | Category B (1) (precoder in O-RU)
25 ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
26 antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
29 mu=0 #15Khz Sub Carrier Spacing
30 ttiPeriod=1000 # in us TTI period (15Khz default 1000us)
31 nDLAbsFrePointA=2645460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
32 nULAbsFrePointA=2525460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
33 nDLBandwidth=10 #Carrier bandwidth for in MHz. Value: 5->400
34 nULBandwidth=10 #Carrier bandwidth for in MHz. Value: 5->400
38 nFrameDuplexType=0 # 0 - FDD 1 - TDD
39 nTddPeriod=0 #TDD priod e.g. DDDS 4
41 MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
42 #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
43 Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
50 duMac0=00:11:22:33:44:66 # asigned MAC of O-DU VF
51 ruMac0=00:11:22:33:44:55 # O-RU VF for O-RU app
52 duMac1=00:11:22:33:44:66 # asigned MAC of O-DU VF
53 ruMac1=00:11:22:33:44:55 # O-RU VF for O-RU app
56 duMac2=00:11:22:33:44:77 # asigned MAC of O-DU VF
57 ruMac2=00:11:22:33:44:44 # O-RU VF for O-RU app
58 duMac3=00:11:22:33:44:77 # asigned MAC of O-DU VF
59 ruMac3=00:11:22:33:44:44 # O-RU VF for O-RU app
61 numSlots=20 #number of slots per IQ files
62 antC0=./usecase/lte_a/mu0_10mhz/ant_0.bin #CC0
63 antC1=./usecase/lte_a/mu0_10mhz/ant_1.bin #CC0
64 antC2=./usecase/lte_a/mu0_10mhz/ant_2.bin #CC0
65 antC3=./usecase/lte_a/mu0_10mhz/ant_3.bin #CC0
66 antC4=./usecase/lte_a/mu0_10mhz/ant_4.bin #CC1
67 antC5=./usecase/lte_a/mu0_10mhz/ant_5.bin #CC1
68 antC6=./usecase/lte_a/mu0_10mhz/ant_6.bin #CC1
69 antC7=./usecase/lte_a/mu0_10mhz/ant_7.bin #CC1
70 antC8=./usecase/lte_a/mu0_10mhz/ant_8.bin #CC2
71 antC9=./usecase/lte_a/mu0_10mhz/ant_9.bin #CC2
72 antC10=./usecase/lte_a/mu0_10mhz/ant_10.bin #CC2
73 antC11=./usecase/lte_a/mu0_10mhz/ant_11.bin #CC2
74 antC12=./usecase/lte_a/mu0_10mhz/ant_12.bin #CC3
75 antC13=./usecase/lte_a/mu0_10mhz/ant_13.bin #CC3
76 antC14=./usecase/lte_a/mu0_10mhz/ant_14.bin #CC3
77 antC15=./usecase/lte_a/mu0_10mhz/ant_15.bin #CC3
79 ## RACH TODO: update for PRACH
80 rachEnable=0 # Enable (1)| disable (0) PRACH configuration
81 #rachOffset=43 # RB offset for prach detection (see RIU spec)
82 #rachCfgIdx=14 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
84 ## control of IQ byte order
85 iqswap=0 #do swap of IQ before send buffer to eth
86 nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
89 debugStop=1 #stop app on 1pps boundary (gps_second % 30)
90 debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
91 bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
93 CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
94 c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
95 u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
98 totalBFWeights=32 # Total number of Beamforming Weights on RU
101 DU_Port_ID_bitwidth=2
102 BandSector_ID_bitwidth=3
104 RU_Port_ID_bitwidth=8
106 # LTE-FDD-FR1-CAT-A-NoBF / LTE-FDD-FR1-CAT-A-DBF
107 # O-RAN.WG4.IOT.0-v02.00
108 # Table A.2.3.2-1: LTE FDD IOT Profile 2 - LTE-FDD-FR1-CAT-A-NoBF
111 ##Transmission Window
115 #Reception Window U-plane
129 ##Transmission Window Fast C-plane UL
133 #Reception Window C-plane UL
134 T2a_max_cp_ul=356 #in us
135 T2a_min_cp_ul=125 #in us
137 ###########################################################
140 #Transmission Window Fast C-plane DL
141 T1a_max_cp_dl=562 #in T1a_max_up + Tcp_adv_dl as per Annex B
142 T1a_min_cp_dl=491 #in T1a_min_up + Tcp_adv_dl as per Annex B
144 #O-RU Reception Window C-plane DL
145 T2a_max_cp_dl=562 #in T2a_max_up + Tcp_adv_dl as per Annex B
146 T2a_min_cp_dl=331 #in T2a_min_up + Tcp_adv_dl as per Annex B
147 ###########################################################