X-Git-Url: https://gerrit.o-ran-sc.org/r/gitweb?p=o-du%2Fphy.git;a=blobdiff_plain;f=fhi_lib%2Fapp%2Fusecase%2Fmu0_20mhz%2Fconfig_file_o_ru.dat;fp=fhi_lib%2Fapp%2Fusecase%2Fmu0_20mhz%2Fconfig_file_o_ru.dat;h=e6befa18cbe3bf6759c34fbb88b515d21f44733f;hp=0000000000000000000000000000000000000000;hb=cef07f74965b1749dd909fc1322e211489fea2ea;hpb=bc60e3a69129edf1c21a01683f84a77483f6e3cc

diff --git a/fhi_lib/app/usecase/mu0_20mhz/config_file_o_ru.dat b/fhi_lib/app/usecase/mu0_20mhz/config_file_o_ru.dat
new file mode 100644
index 0000000..e6befa1
--- /dev/null
+++ b/fhi_lib/app/usecase/mu0_20mhz/config_file_o_ru.dat
@@ -0,0 +1,111 @@
+#######################################################################
+#
+# <COPYRIGHT_TAG>
+#
+#######################################################################
+
+# This is simple configuration file. Use '#' sign for comments
+appMode=1 # lls-CU(0) | RU(1)
+xranMode=0 # Category A  (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
+ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 4)
+antNum=4 # Number of Antennas per CC (default: 4)
+
+##Numerology
+mu=0 #15Khz Sub Carrier Spacing
+ttiPeriod=1000 # in us TTI period (15Khz default 1000us)
+nDLAbsFrePointA=2645460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nULAbsFrePointA=2525460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
+nDLBandwidth=20 #Carrier bandwidth for in MHz. Value: 5->400
+nULBandwidth=20 #Carrier bandwidth for in MHz. Value: 5->400
+nDLFftSize=2048
+nULFftSize=2048
+
+nFrameDuplexType=0 # 0 - FDD 1 - TDD
+nTddPeriod=0 #TDD priod e.g. DDDS 4
+
+MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single 
+ #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
+
+llsCUMac=00:11:22:33:44:66 # asigned MAC of lls-CU VF
+#llsCUMac=3c:fd:fe:a8:e0:70
+ruMac=00:11:22:33:44:55  #RU VF for RU app
+antC0=./usecase/mu0_20mhz/ant_0.bin   #CC0
+antC1=./usecase/mu0_20mhz/ant_1.bin   #CC0
+antC2=./usecase/mu0_20mhz/ant_2.bin   #CC0
+antC3=./usecase/mu0_20mhz/ant_3.bin   #CC0
+antC4=./usecase/mu0_20mhz/ant_4.bin   #CC1
+antC5=./usecase/mu0_20mhz/ant_5.bin   #CC1
+antC6=./usecase/mu0_20mhz/ant_6.bin   #CC1
+antC7=./usecase/mu0_20mhz/ant_7.bin   #CC1
+antC8=./usecase/mu0_20mhz/ant_8.bin   #CC2
+antC9=./usecase/mu0_20mhz/ant_9.bin   #CC2
+antC10=./usecase/mu0_20mhz/ant_10.bin #CC2
+antC11=./usecase/mu0_20mhz/ant_11.bin #CC2
+antC12=./usecase/mu0_20mhz/ant_12.bin #CC3
+antC13=./usecase/mu0_20mhz/ant_13.bin #CC3
+antC14=./usecase/mu0_20mhz/ant_14.bin #CC3
+antC15=./usecase/mu0_20mhz/ant_15.bin #CC3
+
+## RACH TODO: update for PRACH
+rachEanble=1 # Enable (1)| disable (0) PRACH configuration
+#rachOffset=43 # RB offset for prach detection (see RIU spec)
+prachConfigIndex=189 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
+
+antPrachC0=./usecase/mu0_20mhz/ant_0.bin
+antPrachC1=./usecase/mu0_20mhz/ant_1.bin
+antPrachC3=./usecase/mu0_20mhz/ant_3.bin
+antPrachC4=./usecase/mu0_20mhz/ant_4.bin
+
+## control of IQ byte order
+iqswap=0 #do swap of IQ before send buffer to eth
+nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
+
+##Debug
+debugStop=0 #stop app on 1pps boundary (gps_second % 30)
+debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
+
+CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled
+c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
+u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
+
+##RU Settings
+Tadv_cp_dl=25 #in us  TODO: update per RU implementation
+              #C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages
+
+#Reception Window C-plane DL
+T2a_min_cp_dl=400  #in us  
+T2a_max_cp_dl=1120 #in us 
+
+#Reception Window C-plane UL
+T2a_min_cp_ul=400 #in us  
+T2a_max_cp_ul=1120 #in us 
+
+#Reception Window U-plane
+T2a_min_up=200  # in us
+T2a_max_up=1120 # in us
+
+#Transmission Window
+Ta3_min=160 #in us
+Ta3_max=256 #in us
+
+###########################################################
+##lls-CU Settings
+#C-plane
+#Transmission Window Fast C-plane DL
+T1a_min_cp_dl=560
+T1a_max_cp_dl=800
+
+##Transmission Window Fast C-plane UL
+T1a_min_cp_ul=480
+T1a_max_cp_ul=560
+
+#U-plane
+##Transmission Window
+T1a_min_up=280
+T1a_max_up=400
+
+#Reception Window
+Ta4_min=0
+Ta4_max=360
+###########################################################
+