####################################################################### # # # ####################################################################### # This is simple configuration file. Use '#' sign for comments appMode=0 # lls-CU(0) | RU(1) xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU) ccNum=1 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 4) antNum=4 # Number of Antennas per CC (default: 4) ##Numerology mu=1 #30Khz Sub Carrier Spacing ttiPeriod=500 # in us TTI period (30Khz default 500us) nDLAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000 nULAbsFrePointA=3568160 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000 nDLBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400 nULBandwidth=100 #Carrier bandwidth for in MHz. Value: 5->400 nDLFftSize=4096 nULFftSize=4096 nFrameDuplexType=1 # 0 - FDD 1 - TDD nTddPeriod=10 #[0-9] DDDSUUDDDD, for S it’s 6:4:4 sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD sSlotConfig3=0,0,0,0,0,0,2,2,2,2,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD sSlotConfig4=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD sSlotConfig5=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD sSlotConfig6=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD sSlotConfig7=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD sSlotConfig8=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD sSlotConfig9=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame) llsCUMac=00:11:22:33:44:66 # asigned MAC of lls-CU VF ruMac=00:11:22:33:44:55 # RU VF for RU app #ruMac=3c:fd:fe:9e:93:68 #RU PF for tcpdump numSlots=40 #number of slots per IQ files antC0=./usecase/mu1_100mhz/ant_0.bin #CC0 antC1=./usecase/mu1_100mhz/ant_1.bin #CC0 antC2=./usecase/mu1_100mhz/ant_2.bin #CC0 antC3=./usecase/mu1_100mhz/ant_3.bin #CC0 antC4=./usecase/mu1_100mhz/ant_4.bin #CC1 antC5=./usecase/mu1_100mhz/ant_5.bin #CC1 antC6=./usecase/mu1_100mhz/ant_6.bin #CC1 antC7=./usecase/mu1_100mhz/ant_7.bin #CC1 antC8=./usecase/mu1_100mhz/ant_8.bin #CC2 antC9=./usecase/mu1_100mhz/ant_9.bin #CC2 antC10=./usecase/mu1_100mhz/ant_10.bin #CC2 antC11=./usecase/mu1_100mhz/ant_11.bin #CC2 antC12=./usecase/mu1_100mhz/ant_12.bin #CC3 antC13=./usecase/mu1_100mhz/ant_13.bin #CC3 antC14=./usecase/mu1_100mhz/ant_14.bin #CC3 antC15=./usecase/mu1_100mhz/ant_15.bin #CC3 rachEanble=1 # Enable (1)| disable (0) PRACH configuration ## control of IQ byte order iqswap=0 #do swap of IQ before send buffer to eth nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order ##Debug debugStop=1 #stop app on 1pps boundary (gps_second % 30) debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary CPenable=1 #(1) C-Plane is enabled| (0) C-Plane is disabled c_plane_vlan_tag=1 #VLAN Tag used for C-Plane u_plane_vlan_tag=2 #VLAN Tag used for U-Plane ##RU Settings Tadv_cp_dl=25 # in us # C-Plane messages must arrive at the RU some amount of time in advance (Tcp_adv_dl) of the corresponding U-Plane messages #Reception Window C-plane DL T2a_min_cp_dl=285 # 285.42us T2a_max_cp_dl=429 # 428.12us #Reception Window C-plane UL T2a_min_cp_ul=285 # 285.42us T2a_max_cp_ul=429 # 428.12us #Reception Window U-plane T2a_min_up=71 # 71.35in us T2a_max_up=428 # 428.12us #Transmission Window Ta3_min=20 # in us Ta3_max=32 # in us ########################################################### ##lls-CU Settings #C-plane #Transmission Window Fast C-plane DL T1a_min_cp_dl=285 T1a_max_cp_dl=429 ##Transmission Window Fast C-plane UL T1a_min_cp_ul=285 T1a_max_cp_ul=300 #U-plane ##Transmission Window T1a_min_up=96 #71 + 25 us T1a_max_up=196 #71 + 25 us #Reception Window Ta4_min=0 # in us Ta4_max=75 # in us ###########################################################