X-Git-Url: https://gerrit.o-ran-sc.org/r/gitweb?a=blobdiff_plain;f=docs%2Fuser-guide.rst;h=8a1f7b60e16bbc1a03ef5566aeb633b245ab5871;hb=refs%2Fchanges%2F91%2F5391%2F11;hp=cefed4b00c931ef6a9f2ddad088d804cff61dc89;hpb=135666f5b7d048c76f68c15bd0c6b6566d1e49e2;p=o-du%2Fl2.git

diff --git a/docs/user-guide.rst b/docs/user-guide.rst
index cefed4b00..8a1f7b60e 100644
--- a/docs/user-guide.rst
+++ b/docs/user-guide.rst
@@ -5,6 +5,7 @@ User Guide
 ***********
 
 This is the user guide for Cherry release of O-DU/l2.
+Follow installation-guide to get all the dependencies ready.
 
 .. contents::
    :depth: 3
@@ -23,7 +24,35 @@ I. Execution - On locally compiling O-DU High Source Code
    b. ifconfig <interface name>:CU_STUB "192.168.130.82"
    c. ifconfig <interface name>:RIC_STUB "192.168.130.80"
 
-2. Execute CU Stub:
+2. Execute O1 (only if O-DU is built with O1 interface enabled):
+
+   a. Navigate to O1 build folder
+
+      - cd <O-DU High Directory>/l2/build/o1
+ 
+   b. Create a new netconf user and install the YANG module
+      
+      Switch to root user and run following commands
+      
+      | adduser --system netconf && \\
+      |    echo "netconf:netconf" | chpasswd
+
+      | mkdir -p /home/netconf/.ssh && \\
+      | ssh-keygen -A && \\
+      | ssh-keygen -t dsa -P '' -f /home/netconf/.ssh/id_dsa && \\
+      |    cat /home/netconf/.ssh/id_dsa.pub > /home/netconf/.ssh/authorized_keys
+
+      sysrepoctl -i ./yang/o-ran-sc-odu-alarm-v1.yang
+
+   c. Navigate to O1 execution folder
+
+      - cd <O-DU High Directory>/l2/build/o1/bin/o1
+
+   d. Run O1 binary
+      
+      - ./o1
+
+3. Execute CU Stub:
 
    a. Navigate to CU execution folder
 
@@ -33,7 +62,7 @@ I. Execution - On locally compiling O-DU High Source Code
 
       - ./cu_stub
 
-3. Execute RIC Stub:
+4. Execute RIC Stub:
 
    a. Navigate to RIC execution folder
 
@@ -43,7 +72,7 @@ I. Execution - On locally compiling O-DU High Source Code
 
       - ./ric_stub
 
-4. Execute O-DU High:
+5. Execute O-DU High:
 
    a. Navigate to ODU execution folder
 
@@ -53,7 +82,7 @@ I. Execution - On locally compiling O-DU High Source Code
 
       - ./odu
 
-PS: CU stub and RIC stub must be run (in no particular sequence) before ODU
+PS: CU stub and RIC stub must be run (in no particular sequence) before ODU. If O-DU High is built with O1 interface enabled, the O1 binary must be run before all other binaries.
 
 II. Execution - Using Docker Images
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
@@ -82,8 +111,22 @@ This section describes the changes required in compilation and execution of O-DU
 with Intel O-DU Low in timer mode.
 
 
-I. Compilation
-^^^^^^^^^^^^^^
+I. Pre-requisites
+^^^^^^^^^^^^^^^^^^
+
+   1. Install O-DU High as per installation-guide . 
+
+   2. Clone O-DU Low code in <O-DU Low Directory> from
+
+      a. https://gerrit.o-ran-sc.org/r/admin/repos/o-du/phy and,
+
+      b. https://github.com/intel/FlexRAN
+      
+   3. Install O-DU Low as per https://docs.o-ran-sc.org/projects/o-ran-sc-o-du-phy/en/latest/index.html .
+
+
+II. Compilation
+^^^^^^^^^^^^^^^^
 
    1. Build ODU :
 
@@ -115,8 +158,8 @@ I. Compilation
          - make odu PHY=INTEL_L1 PHY_MODE=TIMER MACHINE=BIT64 MODE=FDD
 
 
-II. Execution
-^^^^^^^^^^^^^
+III. Execution
+^^^^^^^^^^^^^^^
 
    1. Execute O-DU Low:
 
@@ -178,10 +221,50 @@ Following diagram shows P5 messages exchanged with O-DU Low in timer mode.
 
 .. figure:: O-DU_High_Low_Flow.jpg
   :width: 600
-  :alt: Figure 1 O-DU High - O-DU Low Message Flow Diagram
+  :alt: Figure 7 O-DU High - O-DU Low Message Flow Diagram
 
-  Figure 5 - O-DU High - O-DU Low Message Flow Diagram
+  Figure 7 - O-DU High - O-DU Low Message Flow Diagram
 
 Note: UL IQ-Sample request and response are needed by Intel O-DU Low in timer mode(testing mode) only. Code changes for
 these are guarded under INTEL_TIMER_MODE flag which can be enabled using compilation option "PHY_MODE=TIMER", as
 mentioned in section B.I.1.d .
+
+
+D. Health Check execution: get alarm-list
+-------------------------------------------
+
+To execute the get alarm-list flow, following steps are required to be executed:
+
+   1.	Start Netconf netopeer client 
+   
+   2. Connect to the server with 
+
+      | user: netconf
+      | pwd:  netconf
+
+   3. Send a Netconf get request for alarms xpath
+
+Here are the steps as executed in the terminal 
+
+     |  netopeer2-cli
+     |  > connect --login netconf
+     |  Interactive SSH Authentication
+     |  Type your password:
+     |  Password:
+     |  > get --filter-xpath /o-ran-sc-odu-alarm-v1\:odu/alarms
+     |  DATA
+     |  <odu xmlns=\"urn\:o-ran\:odu\:alarm\:1.0\">
+     |    <alarms>
+     |      <alarm>
+     |        <alarm-id>1009</alarm-id>
+     |        <alarm-text>cell id  [1] is up</alarm-text>
+     |        <severity>2</severity>
+     |        <status>Active</status>
+     |        <additional-info>cell UP</additional-info>
+     |      </alarm>
+     |    </alarms>
+     |  </odu>
+
+The XML output is a list of active alarms in the O-DU High system.
+
+Note: Integration with SMO/OAM is not yet done so a Netconf CLI client(netopeer2-cli) is used to connect to the Netconf server and send the get request.