.. This work is licensed under a Creative Commons Attribution 4.0 International License.
.. http://creativecommons.org/licenses/by/4.0
-
-
+.. Copyright (C) 2021 Nordix
Installation Guide
==================
-.. contents::
- :depth: 3
- :local:
-
Abstract
--------
-This document describes how to install the Non-RT RIC dashboard, its dependencies and required system resources.
-
-
-Version history
-
-+--------------------+--------------------+--------------------+--------------------+
-| **Date** | **Ver.** | **Author** | **Comment** |
-| | | | |
-+--------------------+--------------------+--------------------+--------------------+
-| 20XX-XX-XX | 0.1.0 | | First draft |
-| | | | |
-+--------------------+--------------------+--------------------+--------------------+
-| | 0.1.1 | | |
-| | | | |
-+--------------------+--------------------+--------------------+--------------------+
-| | 1.0 | | |
-| | | | |
-| | | | |
-+--------------------+--------------------+--------------------+--------------------+
-
-
-Introduction
-------------
-
-.. <INTRODUCTION TO THE SCOPE AND INTENTION OF THIS DOCUMENT AS WELL AS TO THE SYSTEM TO BE INSTALLED>
-
-.<EXAMPLE>:
-
-This document describes the supported software and hardware configurations for the reference component as well as providing guidelines on how to install and configure such reference system.
-
-The audience of this document is assumed to have good knowledge in RAN network and Linux system.
-
-
-Preface
--------
-.. <DESCRIBE NEEDED PREREQUISITES, PLANNING, ETC.>
-
-<EXAMPLE>:
-
-Before starting the installation of <project name>, some planning must precede.
-
-.. note:any preperation you need before setting up sotfware and hardware
-
-
-Hardware Requirements
----------------------
-.. <PROVIDE A LIST OF MINIMUM HARDWARE REQUIREMENTS NEEDED FOR THE INSTALL>
-
-<EXAMPLE>:
-
-Following minimum hardware requirements must be met for installation of <project name>:
-
-+--------------------+----------------------------------------------------+
-| **HW Aspect** | **Requirement** |
-| | |
-+--------------------+----------------------------------------------------+
-| **# of servers** | |
-+--------------------+----------------------------------------------------+
-| **CPU** | |
-| | |
-+--------------------+----------------------------------------------------+
-| **RAM** | |
-| | |
-+--------------------+----------------------------------------------------+
-| **Disk** | |
-| | |
-+--------------------+----------------------------------------------------+
-| **NICs** | |
-| | |
-| | |
-| | |
-| | |
-| | |
-+--------------------+----------------------------------------------------+
-
-
+This document describes how to install the Non-RT RIC components, their dependencies and required system resources.
Software Installation and Deployment
------------------------------------
-.. <DESCRIBE THE FULL PROCEDURES FOR THE INSTALLATION OF THE O-RAN COMPONENT INSTALLATION AND DEPLOYMENT>
-<EXAMPLE>:
+Install with Docker
++++++++++++++++++++
-This section describes the installation of the <project name> installation on the reference hardware.
+Docker compose files are provided, in the "docker-compose" folder, to install the components. Run the following
+command to start the components:
+ .. code-block:: bash
+ docker-compose -f docker-compose.yaml
+ -f policy-service/docker-compose.yaml
+ -f ics/docker-compose.yaml
-References
-----------
-.. <PROVIDE NEEDED/USEFUL REFERENCES>
+The example above is just an example to start some of the components.
+For more information on running and configuring the functions can be found in the README file in the "`docker-compose <https://gerrit.o-ran-sc.org/r/gitweb?p=nonrtric.git;a=tree;f=docker-compose>`__" folder, and on the `wiki page <https://wiki.o-ran-sc.org/display/RICNR/Release+E+-+Run+in+Docker>`_
+Install with Helm
++++++++++++++++++
+Helm charts and an example recipe are provided in the `it/dep repo <https://gerrit.o-ran-sc.org/r/admin/repos/it/dep>`_,
+under "nonrtric". By modifying the variables named "installXXX" in the beginning of the example recipe file, which
+components that will be installed can be controlled. Then the components can be installed and started by running the
+following command:
+ .. code-block:: bash
+ bin/deploy-nonrtric -f nonrtric/RECIPE_EXAMPLE/example_recipe.yaml