1 #******************************************************************************
3 # Copyright (c) 2019 Intel.
5 # Licensed under the Apache License, Version 2.0 (the "License");
6 # you may not use this file except in compliance with the License.
7 # You may obtain a copy of the License at
9 # http://www.apache.org/licenses/LICENSE-2.0
11 # Unless required by applicable law or agreed to in writing, software
12 # distributed under the License is distributed on an "AS IS" BASIS,
13 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
14 # See the License for the specific language governing permissions and
15 # limitations under the License.
17 #******************************************************************************/
19 # This is simple configuration file. Use '#' sign for comments
20 instanceId=1 # 0,1,2,... in case more than 1 application started on the same system
21 appMode=1 # O-DU(0) | O-RU(1)
22 xranRanTech=1 # 5G-NR (0) | LTE (1)
23 xranMode=0 # Category A (0) (precoder in lls-CU) | Category B (1) (precoder in RU)
24 ccNum=6 # Number of Componnent Carriers (CC) per ETH port with XRAN protocol (default:1 max: 12)
25 antNum=4 # Number of Antennas per CC (default: 4) or number of Digital streams for Category B
28 mu=0 #15Khz Sub Carrier Spacing
29 ttiPeriod=1000 # in us TTI period (15Khz default 1000us)
30 nDLAbsFrePointA=2645460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
31 nULAbsFrePointA=2525460 #nAbsFrePointA - Abs Freq Point A of the Carrier Center Frequency for in KHz Value: 450000->52600000
32 nDLBandwidth=10 #Carrier bandwidth for in MHz. Value: 5->400
33 nULBandwidth=10 #Carrier bandwidth for in MHz. Value: 5->400
37 nFrameDuplexType=1 # 0 - FDD 1 - TDD
38 nTddPeriod=5 #[0-4] DDDSU, for S it's 10:2:2
39 sSlotConfig0=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
40 sSlotConfig1=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
41 sSlotConfig2=0,0,0,0,0,0,0,0,0,0,0,0,0,0 # (0) - DL (1) - UL (2) - GUARD
42 sSlotConfig3=0,0,0,0,0,0,0,0,0,0,2,2,1,1 # (0) - DL (1) - UL (2) - GUARD
43 sSlotConfig4=1,1,1,1,1,1,1,1,1,1,1,1,1,1 # (0) - DL (1) - UL (2) - GUARD
45 MTUSize=9600 #maximum transmission unit (MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single
46 #xRAN network layer transaction. supported 1500 bytes and 9600 bytes (Jumbo Frame)
47 Gps_Alpha=0 #alpha and beta value as in section 9.7.2 of ORAN spec
53 numSlots=20 #number of slots per IQ files
54 antC0=./usecase/dss/mu0_10mhz/ant_0.bin #CC0
55 antC1=./usecase/dss/mu0_10mhz/ant_1.bin #CC0
56 antC2=./usecase/dss/mu0_10mhz/ant_2.bin #CC0
57 antC3=./usecase/dss/mu0_10mhz/ant_3.bin #CC0
58 antC4=./usecase/dss/mu0_10mhz/ant_0.bin #CC1
59 antC5=./usecase/dss/mu0_10mhz/ant_1.bin #CC1
60 antC6=./usecase/dss/mu0_10mhz/ant_2.bin #CC1
61 antC7=./usecase/dss/mu0_10mhz/ant_3.bin #CC1
62 antC8=./usecase/dss/mu0_10mhz/ant_0.bin #CC2
63 antC9=./usecase/dss/mu0_10mhz/ant_1.bin #CC2
64 antC10=./usecase/dss/mu0_10mhz/ant_2.bin #CC2
65 antC11=./usecase/dss/mu0_10mhz/ant_3.bin #CC2
66 antC12=./usecase/dss/mu0_10mhz/ant_0.bin #CC3
67 antC13=./usecase/dss/mu0_10mhz/ant_1.bin #CC3
68 antC14=./usecase/dss/mu0_10mhz/ant_2.bin #CC3
69 antC15=./usecase/dss/mu0_10mhz/ant_3.bin #CC3
70 antC16=./usecase/dss/mu0_10mhz/ant_0.bin #CC4
71 antC17=./usecase/dss/mu0_10mhz/ant_1.bin #CC4
72 antC18=./usecase/dss/mu0_10mhz/ant_2.bin #CC4
73 antC19=./usecase/dss/mu0_10mhz/ant_3.bin #CC4
74 antC20=./usecase/dss/mu0_10mhz/ant_0.bin #CC5
75 antC21=./usecase/dss/mu0_10mhz/ant_1.bin #CC5
76 antC22=./usecase/dss/mu0_10mhz/ant_2.bin #CC5
77 antC23=./usecase/dss/mu0_10mhz/ant_3.bin #CC5
79 ## RACH TODO: update for PRACH
80 rachEnable=0 # Enable (1)| disable (0) PRACH configuration
81 #rachOffset=43 # RB offset for prach detection (see RIU spec)
82 prachConfigIndex=189 # PRACH config index as per TS36.211 - Table 5.7.1-2 : PRACH Configuration Index
84 antPrachC0=./usecase/lte_a/mu0_20mhz/ant_0.bin
85 antPrachC1=./usecase/lte_a/mu0_20mhz/ant_1.bin
86 antPrachC2=./usecase/lte_a/mu0_20mhz/ant_2.bin
87 antPrachC3=./usecase/lte_a/mu0_20mhz/ant_3.bin
89 ###########################################################
91 dssEnable=1 # Enable (1)| disable (0) - flag to enable extType-9
93 technology=1,1,0,0,1 #Consider each comma separated value as a technology(NR/LTE) for a given slot. 1-NR, 0-LTE. this pattern repeats after every dssPeriod
94 ###########################################################
96 ## control of IQ byte order
97 iqswap=0 #do swap of IQ before send buffer to eth
98 nebyteorderswap=1 #do swap of byte order for each I and Q from CPU byte order to network byte order
101 debugStop=1 #stop app on 1pps boundary (gps_second % 30)
102 debugStopCount=0 #if this value is >0 then stop app after x transmission packets, otherwise app will stop at 1pps boundary
103 bbdevMode=-1 #bbdev mode, -1 = not use bbdev, 0: use software mode, 1: use hardware mode
105 CPenable=0 #(1) C-Plane is enabled| (0) C-Plane is disabled
106 c_plane_vlan_tag=1 #VLAN Tag used for C-Plane
107 u_plane_vlan_tag=2 #VLAN Tag used for U-Plane
110 totalBFWeights=32 # Total number of Beamforming Weights on RU
113 DU_Port_ID_bitwidth=2
114 BandSector_ID_bitwidth=3
116 RU_Port_ID_bitwidth=8
118 # LTE-FDD-FR1-CAT-A-NoBF / LTE-FDD-FR1-CAT-A-DBF
119 # O-RAN.WG4.IOT.0-v02.00
120 # Table A.2.3.2-1: LTE FDD IOT Profile 2 - LTE-FDD-FR1-CAT-A-NoBF
123 ##Transmission Window
127 #Reception Window U-plane
141 ##Transmission Window Fast C-plane UL
145 #Reception Window C-plane UL
146 T2a_max_cp_ul=356 #in us
147 T2a_min_cp_ul=125 #in us
149 ###########################################################
152 #Transmission Window Fast C-plane DL
153 T1a_max_cp_dl=562 #in T1a_max_up + Tcp_adv_dl as per Annex B
154 T1a_min_cp_dl=491 #in T1a_min_up + Tcp_adv_dl as per Annex B
156 #O-RU Reception Window C-plane DL
157 T2a_max_cp_dl=562 #in T2a_max_up + Tcp_adv_dl as per Annex B
158 T2a_min_cp_dl=331 #in T2a_min_up + Tcp_adv_dl as per Annex B
159 ###########################################################